Course catalogue

Innhold

Kurset omfatter de krav som stilles i STCW-F konvensjonens kapittel III, regel 1, pkt 1: 1,1, 1,2 1.3, 1,4, 1,5 og 1,6 og omfatter:

Personlige redningsteknikker

Forebyggende brannvern og brannslokking

Grunnleggende førstehjelp

Personlig sikkerhet og omsorg for menneskeliv og miljø

Den første kursdagen gjennomføres som selvstudie på e-læring utenfor kurssenteret, og den siste gjennomføres som praktisk opplæring på kurssenteret. E-læringen kan gjennomføres når det passer deg best, så lenge den er fullført før du møter til praksisdagen.

Link til e-læringen sendes fra Knowledge portal.

Varighet

E-læringen tar ca 7 klokketimer å gjennomføre.

Praksisdagen utgjør 1 dag på kurssenter.

1 dag på kurssenter er 8 skoletimer

1 skoletime er 45 minutt

Innlevering

E-læringen må være gjennomført og bestått FØR du møter til praktisk kursdag på kurssenteret.

Innhold

Dette kurset tilfredsstiller kravene til Sikkerhetsopplæring for sjøfolk på skip med lengde (L) under 24 meter i fartsområde liten kystfart.

Kurset gir i utgangspunktet ikke tilstrekkelig sikkerhetsopplæring for sjøfolk på:

Lasteskip med lengde (L) over 24 meter

Lasteskip med bruttotonnasje over 500

Lasteskip i større fartsområder enn liten kystfart

Passasjerskip med passasjersertifikat for 13 eller flere passasjerer

Fiskefartøy uansett størrelse og fartsområde

Emnene i kurset tar utgangspunkt i STCW-konvensjonens regel VI, Avsnitt A-VI/1 og tabeller A-VI/1-1, 1-2, 1-3 og 1-4, men innhold og omfang er tilpasset til skip med lengde (L) under 24 meter i fartsområde liten kystfart eller mindre.

Etter gjennomført kurs vil du ha kunnskap om:

Personlige redningsteknikker

Forebyggende brannvern og brannslukking

Grunnleggende førstehjelp

Personlig sikkerhet og omsorg for menneskeliv og miljø

Varighet

Kursets varighet er 3,5 dag, hvorav 1,5 dag av kurset gjennomføres som e-læring på egenhånd, før ankomst kurssenteret. 

1 kursdag er 10 skoletimer

1 skoletime er 45 minutt

Innlevering

E-læring sendt fra Knowlegde portal må være fullført før deltaker møter til kursstart på kurssenteret. 

The objectives of the training is to provide prospective crane operators a good theoretical basic training in safe use of offshore cranesThe training will give the candidate  a good understanding of the principles of offshore construction, operation, maintenance and usage so that incidents and accidents during lifting operations are avoided.

Introduction

Definition

Area for using the offshore crane

Accidents related to offshore crane

Regulation, standards

Requirements for crane operator

Structure, construction, assembly and boom construction

Electrical, hydraulic, mechanics

Load diagram

Safety equipment

Winch, wire rope, blocks

Maintenance and inspection

Certification, documentation

Safe use of offshore crane

Simulator practice

Work task

Exam

"Users of an approved maritime VHF equipment shall have a Short Range Certificate (SRC). Earlier this this was called VHF license, 
 but syllabus is now adapted to international regulations and the name is changed to SRC.

VHF apparatet

DSC (Digital Selective Calling)

distress, urgency and security

Frequencies, ranges and channels

Communications needs, channels

The vessel's identity,

Certificates, regulations, declaration of silence, medical advice

GMDSS, Navtex, Inmarsat

Emergency radio equipment

Power source

Antennas

The main objective of learning initiative is that it provide training to acquire sufficient knowledge to lead and guide personnel and assess level of personnel who will use the lifting equipment, and personnel who will be deck operators.

Introduction

Mentor/Buddy

Syllabus

Regulation

Roles and responsibility 

Competence requirements

Incident 

Lifting equipment

Mentor/Buddy agreement

Observation technique

Communication

Practical training

Safe lifting operation

Theoretical test

After completed the the training, the candidate should be able to perform a practical test to demonstrate that he/her has acquired sufficient competence to operate the telescopic C2 forklift and carry out varied work task with the same forklift.

Main components, supplementary equipment 

Inspection

Function test

Practical training

Construction

Practical test

The objective of this training is to provide training to acquire adequate knowledge of safe rigger so that accidents are avoided by use.

Theory basic rigging

Communication

Inspection 

Use of lifting equipment

Calculation

Use of rigging Equipment

Chain hois, lever hoist, 

Wire, Chain, fibre, shackle, eyebolts etc.

Core failures

Choker configurations

Practical exercises

Planning of operations

Safe Job Analysis

Procedures

Use of barrier/barrier materials

Implementation of horizontal/vertical movement of loads

Proper use of protective equipment

Assessment of safety during rigging operations

Qualifying scaffolders for assembly, dismantling, modification and inspection of scaffolding with upper decks between 5 and 9 meters in standard alignment.

Introduction

Regulation

Planning of scaffolding

Scaffold construction 5-9m

Allowable loads

anchor/wind forces

Inspection of scaffold

Report of inspection

Measures to reduce risk

Tag/marking

Use of harness equipment

Assemble/dismantling of scaffolding

Evaluation

After completing the course the candidate should independently be able to carry out a periodic inspection within G7.

Introduction

Regulations, guidance, standards

Constructions

Components

Certifications and inspection

Wire/chain drive

Instruction books

Work task

Practical training in inspection winch and hoist

Inspection equipment

Completion of reports

Exam

The objective of this training is that the course participants is updated and acquired basic knowledge and practical skills for the building of scaffolding, so that accidents are avoided by the use and also provide the candidate with knowledge that are in accordance with the regulations. After completing the course, participants will have the necessary knowledge to carry out practical training with a min of 72 hours. Before an employer can set the candidate to work independently, the candidate should have practice work with scaffolding in min.6 months.

Introduction

Safety at work

Regulations

Planning of work in height

Technical Requirements Scaffold Structures

Suspended Scaffolding

Anchoring, bracing, adjustment

Structures under construction

Risk Assessment

Practical control of scaffolding

Working on completed constructions

Assess

Use of harness equipment

Exam

After completing the course, students should know the regulations for the activityBeyond this, be familiar with risk management, consequences of a fall using fall protection equipment and knowledge of the fall protection equipment used in their company.

Introduction

Laws, regulations and standards

Risks of working in heights

Fall, fall forces and loads

Actions to reduce the risk of falls

Collective protection measures

Personal fall prevention measures and anchorages

Actions to mitigate the consequences of falls

Personal protective equipment ( PPE)

Knowledge of emergency work in height

The main objective with the training is to provide training for the candidate to acquire basic practical knowledge about safe use of mobile crane so that accidents are avoided by use.

Main Components

Inspection Points

Arrangement and service

Overturning moment/Stability

Overloadequipment

Practical use of lifting gir

Load chart

Operation technique

Hook/Block

other equipment

After completing course the participants have the necessary skills the Act requires from the managers, enabling them to perform their duties in satisfactory manners.

Working Environment Act/Orders

HSE work

Safety work

Employers duties

Employee’s right and duty to participate

Function and tasks of safety representative

Function and tasks of the working environment committee

Company health service function

Working environment factors

Work environment and work relations 

Inclusive work

Psychosocial work environment

Accidents and accident prevention work

Fall, fall forces and loads

Personal fall prevention measures and anchorages

Personal protective equipment ( PPE)

Knowledge of emergency work in height

When finish with the course the candidate should be able to perform a periodic inspection within G04.

Practical training in operation of bridge-/overhead crane

Practical training in inspection

Inspection procedures

Reports

Tools and equipment

Examens

This regulation-focused course provides shipboard and shore-based personnel with a complete, practical understanding of how to maintain inspection-ready Ballast Water Record Books (BWRB) under the updated requirements entering into force on 1 February 2025.

Anchored in RESOLUTION MEPC.369(80) and the amended Ballast Water Management Convention (2004), the course translates complex IMO provisions into clear, step-by-step documentation methods. Participants learn how to record uptake, exchange, circulation, discharge, internal transfers, bypass events, and failures in a defensible, auditable format. Through real examples, case-based quizzes, and templates, seafarers develop confidence in creating logs that withstand PSC, flag, and company audits.

This course equips seafarers, officers, and superintendents with the psychological tools and operational strategies to maintain composure, clarity, and performance during high-stakes inspections such as SIRE 2.0, CDI, RightShip, PSC, and internal audits. By integrating behavioral science, human performance principles, and real inspection dynamics, it trains participants to manage cognitive load, stress, and communication under scrutiny. Through practical frameworks—such as the “Brief–Execute–Debrief” model, 4-4-6 breathing control, and adaptive communication scripts—crew members learn to demonstrate confidence, factual consistency, and professional discipline under observation.

This course provides comprehensive type-specific familiarization with MAN B&W two-stroke and four-stroke main engines (MC/MC-C, ME/ME-C, ME-GI, ME-LGIM, and ME-LGIP). Designed for engineers, technical managers, and shipboard officers, it bridges OEM standards with onboard practice through detailed diagnostics, maintenance, and optimization procedures. The program focuses on safe operation, emission compliance, and lifecycle management, enabling participants to interpret indicator diagrams, analyze KPIs (SFOC, Pmax, exhaust temperatures), and ensure audit-ready documentation aligned with Class, Flag, and IMO requirements.